The chip45 team is on vacation from 12/02/2024 till 12/05/2024. Orders received during this period will be processed afterwards and the delivery times stated for the products will be extended accordingly by up to 5 days.
Products description
The M-2J1R by Rosahl is a compact flat-membrane dehumidifier module for volumes of up to 250 litres.
Operation Principle
Like all Rosahl dehumidifiers the M-2J1R is based on a solid-state polymer membrane. When supplied with a 3V DC voltage, moisture on one side is being decomposed into Hydrogen ions and Oxygen, the Hydrogen ions pass the membrane and recombine with air Oxygen to moisture again on the other side and get discharged.
Storage of 3D-Print Filament Spools
With an applicaple air volume of 250 liters the Rosahl M-2J1R membrane is suitable for smaller storage dryboxes around 30-50l for multiple spools.
Which Membrane Suits What Application?
The following table reflects our own applications with different membranes and usage scenarios in our climate zone with max. 65-70%RH and could serve as a guide for membrane selection.
(1) This is the specified applicable volume by the manufacturer. For 3D print filament storage at low humidity levels around 15%, we recommend to oversize the membrane at least by a factor of 5 or 6. Achievable end-humidity depends on various factors like box sealing, temperatur, outside humidity level. In regions with high air humidity it might be beneficial to oversize the membrane more.
(2) The Bambu Lab AMS comes with some manufacturing variations and can be less properly sealed as stated. Given this, also an M-1J1R or M-2J1R can give decent results but it is recommended to carefully check for potential leakages and proper/tight gasket sealing before chosing a membrane size. It might hence be beneficial to oversize the membrane more. If in doubt, contact us prior to selecting/ordering.
Power Supply
The Rosahl M-2J1R dehumidifer requires a 3V DC supply voltage and draws in continous operation i.e., when the moisture level in the volume stabilized to a low level, just around 1W power.
Due to the membrane being intrinsically hygroscopic, it absorbs humidity if no supply voltage is present. This moisture needs to be discharged on startup and leads to a significantly higher inrush-current that the regular operating current. During startup the supply voltage shall still not drop below 2V, otherwise moisture discharge is not possible or significantly delayed. Suitable current supplies are fold-back current limiting sources, which regulate the output current further down than pure constant current sources and hence maintain a certain output voltage. We provide suitable USB-C voltage regulator modules with fold-back current limiting, which can be used stand-alone or mounted into our 3D-print mounting frame/covers.
Technical Parameters M-2J1R
| Applicable Volume | ~0,250m³ |
| Dehumidifying Performance | 2g/day |
| Supply Voltage | 2.9-3.3VDC |
| Power Consumption | 1.5W (20°C/60%rH) |
| Rated Current | 500mA (dep. of rH) |
| Inrush Current | 5A |
| Operating Temperature | -10°C - +50°C |
| Connecting Type | Push-Connector/Solder |
Further Information
Scope of Delivery
The Rosahl M-2J1R dehumidifier comes as single unit with gasket.Complete Kits
Full kits with the M-2J1R membrane, VREG2 USB-C power supply module and assembly material will be available soon.Manufacturer Information
RYOSAI TECHNICA CO., LTD., 8-1-1 Tsukaguchi-Honmachi, Amagasaki-City, Hyogo, 661-0001 Japan, Email: ryosai_sales@ryoyo.co.jp
Customers who bought this product also bought the following products:
This Product was added to our catalogue on 16/11/2024.
Rosahl Electric Dehumidifer Membranes »
More information on your personal page »
You can pay with PayPal/PayPal-Express or advance bank transfer. Companies and institutions in Germany can also order against open invoice.